Search all content

821 - 830 of 1762 results
AS 2701-2001 Methods of sampling and testing mortar for masonry construction 2001 cover

Standards Australia

Version:  First Edition 2001.  (Current)
Specifies a range of methods for testing mortar used, or being investigated for use, in the construction of masonry in accordance with AS 3700. It does not cover mortar to be used in thin bed construction.
AS 2404-1980 Textile floor coverings - Fire propagation of the use-surface using a small ignition source 1980 cover

Standards Australia

Version:  First Edition 1980.  (Current)
States the level of fire propagation acceptable for the use-surface of any textile floor covering when ignited using a small ignition source. The methenamine tablet used for the test is specified in AS 2111.18.
AS ISO 10545.6-2013 Ceramic tiles, Part 6: Determination of resistance to deep abrasion for unglazed tiles 2013 cover

Standards Australia

Version:  First Edition 2013.  (Current)
Adopts ISO 10545-6:2010, which specifies a test method for determining the resistance to deep abrasion of all unglazed ceramic tiles used for floor coverings.
AS/NZS 4347.5:1995 Damp-proof courses and flashings - Methods of test, Method 5: Determination of compression properties 1995 cover

Standards Australia/Standards New Zealand

Version:  First Edition 1995.  (Current)
This Standard sets out the method of determining the compressive elastic modulus and compression set of a damp-proof course of nominal thickness not less than 5 mm.
AS/NZS 2272:2006 Plywood - Marine 2006 cover

Standards Australia/Standards New Zealand

Version:  Second Edition 2006.  (Current)
Specifies requirements for the manufacture, grading and finishing of plywood intended for marine use.
AS 1012.18-1996 Methods of testing concrete, Method 18: Determination of setting time of fresh concrete, mortar and grout by penetration resistance 1996 cover

Standards Australia

Version:  Second Edition 1996.  (Current)
Specifies procedures for determining the initial and final setting times of mortar sieved from fresh concrete mix, the slump of which is greater than zero, using penetration resistance needles. This Standard is also applicable to fresh mortar and grout.
AS 1012.1:2014 Methods of testing concrete, Method 1: Sampling of concrete 2014 cover

Standards Australia

Version:  Fourth Edition 2014.  (Current)
This Standard sets out the method for obtaining samples of freshly-mixed concrete (a) directly from mixers; (b) from agitator or non-agitator units; (c) from concrete deposited in readiness for casting; and (d) from concrete deposited in the forms.
AS/NZS 2098.2:2012 Methods of test for veneer and plywood, Method 2: Bond quality of plywood (chisel test) 2012 cover

Standards Australia/Standards New Zealand

Version:  Third Edition 2012.  (Current)
This Standard sets out the method for determining the quality of bond in plywood.
AS/NZS 61439.4:2016 Low-voltage switchgear and controlgear assemblies, Part 4: Particular requirements for assemblies for construction sites (ACS) (IEC 61439-4, Ed. 1.0 (2012), MOD) 2020 cover

Standards Australia/Standards New Zealand

Version:  First Edition 2016.  (Current)
Adopts IEC61439-4, Ed. 1.0 (2012) to provide specific requirements for the design of low-voltage switchgear and controlgear assemblies for use on construction sites.
AS 4046.8:2015 Methods of testing roof tiles, Method 8: Adhesive mechanical fasteners - Flexible pointing 2015 cover

Standards Australia

Version:  Third Edition 2015.  (Current)
Sets out the method for testing flexible pointing to determine its suitability for use as an adhesive flexible pointing after conditioning by prolonged water saturation.