Search all content

551 - 560 of 1778 results
AS 4786.2-2005 Timber flooring, Part 2: Sanding and finishing 2005 cover

Standards Australia

Version:  First Edition 2005.  (Current)
Proposes methods for the sanding and finishing of timber floors including strip flooring and parquet. Information is included for specifiers, on the problems of assessing equilibrium moisture content and on the types of coating systems available..
AS 1141.30.2:2022 Methods for sampling and testing aggregates, Method 30.2: Preparation of aggregate reference specimens for visual comparison 2022 cover

Standards Australia

Version:  Second Edition 2022.  (Current)
AS 1141.30.2:2022 sets out the method for preparing reference specimens that represent each of the visually distinguishable rock types present in a quarried source for use in AS 1141.30.1.
AS/NZS 4455.1:2008 Masonry units, pavers, flags and segmental retaining wall units, Part 1: Masonry units 2008 cover

Standards Australia/Standards New Zealand

Version:  Second Edition 2008.  (Current)
Sets out requirements for masonry units used for walls built in accordance with AS 3700 and NZS 4230.
AS 4256.3-2006 Plastic roof and wall cladding materials, Part 3: Glass fibre reinforced polyester (GRP) 2006 cover

Standards Australia

Version:  First Edition 2006.  (Current)
Specifies requirements for general purpose translucent and opaque glass fibre reinforced polyester sheets of flat, corrugated and other geometrical configurations intended for roof and wall cladding materials.
AS/NZS 61439.2:2016 Low-voltage switchgear and controlgear assemblies, Part 2: Power switchgear and controlgear assemblies (IEC 61439-2, Ed. 2.0 (2011), MOD) 2020 cover

Standards Australia/Standards New Zealand

Version:  First Edition 2016.  (Pending Revision)
Adopts IEC61439-2, Ed. 2.0 (2011) to define specific requirements of power switchgear and controlgear assemblies (PSC-ASSEMBLIES).
AS 1012.11-2000 Methods of testing concrete, Method 11: Determination of the modulus of rupture 2000 cover

Standards Australia

Version:  Third Edition 2000.  (Current)
This Standard sets out a method for determining the modulus of rupture of concrete testspecimens prepared in accordance with AS 1012.8.2 tested as simple beams with third-pointloading.
AS/NZS 4357.2:2006 Structural laminated veneer lumber (LVL), Part 2: Determination of structural properties - Test methods 2006 cover

Standards Australia/Standards New Zealand

Version:  First Edition 2006.  (Current)
Specifies test methods for the determination of structural properties of structural laminated veneer lumber (LVL).
AS 1379-2007 Specification and supply of concrete 2007 cover

Standards Australia

Version:  Fourth Edition 2007.  (Pending Revision)
Sets out minimum requirements for the materials, plant and equipment used in the supply of concrete; the production and, if applicable, the delivery of concrete in the plastic state; specifying, sampling, testing and compliance with specified properties of plastic and hardened concrete; and the uniformity of mixing.
AS 1735.7-1998 Lifts, escalators and moving walks, Part 7: Stairway lifts 1993 cover

Standards Australia

Version:  Fifth Edition 1998.  (Current)
Specifies requirements for power-operated stairway lifts intended for use by persons with limited mobility. The lifts consist of a carriage, incorporating a platform, or a chair, or both, for raising or lowering persons along stairways.
AS/NZS 2111.15:1996 Textile floor coverings - Tests and measurements, Method 15: Determination of tuft withdrawal force 1996 cover

Standards Australia/Standards New Zealand

Version:  First Edition 1996.  (Current)
This Standard describes the method for determining the withdrawal force required to remove tufts from a textile floor covering.