Search all content

701 - 710 of 1754 results
AS/NZS 1050.8:1994 Methods for the analysis of iron and steel, Part 8: Determination of manganese content - Spectrophotometric method 1994 cover

Standards Australia/Standards New Zealand

Version:  First Edition 1994.  (Current)
Specifies a spectrophotometric method for the determination of manganese content between 0.01 percent and 2 percent in all types of iron and steel.
AS/NZS 1050.24:1994 Methods for the analysis of iron and steel, Part 24: Determination of aluminium content - Spectrophotometric method 1994 cover

Standards Australia/Standards New Zealand

Version:  First Edition 1994.  (Current)
Specifies a spectrophotometric method for the determination of aluminium content in the range of 0.002 percent to 1.4 percent aluminium in all types of iron and steel. The method uses a mercury cathode, followed by solvent extraction to separate interfering elements, with alizarin red S to produce a chromogen which is measured at a wavelength of 490 nm.
AS 1141.15-1999 Methods for sampling and testing aggregates, Method 15: Flakiness index 1999 cover

Standards Australia

Version:  Fifth Edition 1999.  (Current)
This Standard sets out a method for determining the flakiness index of an aggregate. The Method applies to aggregates having a nominal size not greater than 63.0 mm and having at least 80% by mass retained on a 4.75 mm sieve. The Method makes reference to a particle size distribution procedure which is required for determination of flakiness index.
AS 1141.25.2-2003 Methods for sampling and testing aggregates, Method 25.2: Degradation factor - Coarse aggregate 2003 cover

Standards Australia

Version:  Second Edition 2003.  (Current)
This Standard sets out the method for the determination of the degradation factor of coarse aggregates. The test categorizes the fines produced by self-abrasion in the presence of water.
AS 1742.13:2023 Manual of uniform traffic control devices, Part 13: Local area traffic management 2023 cover

Standards Australia

Version:  Third Edition 2023.  (Current)
AS 1742.13:2023 specifies requirements for the signs, pavement marking and other devices to be applied to commonly used local area traffic management (LATM) schemes
AS/NZS 4934.1:2014 Incandescent lamps for general lighting service, Part 1: Test methods - Energy performance 2014 cover

Standards Australia/Standards New Zealand

Version:  Second Edition 2014.  (Current)
​This Standard specifies test methods for the energy performance of incandescent lamps, both tungsten filament and tungsten halogen, that are used in general lighting service.
AS/NZS 4347.1:1995 Damp-proof courses and flashings - Methods of test, Method 1: Determination of water permeability 1995 cover

Standards Australia/Standards New Zealand

Version:  First Edition 1995.  (Current)
This Standard sets out the method of determining the water permeability of damp-proof courses and flashings.
AS/NZS 2111.4:1996 Textile floor coverings - Tests and measurements, Method 4: Determination of surface pile mass above the substrate 1996 cover

Standards Australia/Standards New Zealand

Version:  First Edition 1996.  (Current)
This Standard describes the procedure for determining the mass per unit area of surface pile, which can be cut from above the substrate of a textile floor covering. The surface pile mass per unit area can be expressed at its equilibrium condition or in terms of clean conditioned mass at agreed commercial allowances.
AS 1012.6:2014 Methods of testing concrete, Method 6: Determination of bleeding of concrete 2014 cover

Standards Australia

Version:  Fourth Edition 2014.  (Current)
Sets out the method for determining the relative quantity and rate that mixing water will bleed from a sample of freshly mixed concrete under the conditions of the test.
AS/NZS 1050.26:1994 Methods for the analysis of iron and steel, Part 26: Silicon in iron and steel - Spectrophotometric method 1994 cover

Standards Australia/Standards New Zealand

Version:  Second Edition 1994.  (Current)
Specifies a spectrophotometric method using reduced ß-silicomolybdate complex, for the determination of the total silicon content of iron and steel. The method covers the range 0.005 percent to 5.0 percent silicon and is applicable to all grades of iron and steel.