Search all content

511 - 520 of 1313 results
AS 10002:2022 Guidelines for complaint management in organizations (ISO 10002:2018, NEQ) 2022 cover

Standards Australia

Version:  Second Edition 2022.  (Current)
Provides guidance on complaint management within all types of organizations, including the planning, design, implementation, operation, maintenance and improvement of a complaint management system.
AS 2890.2:2018 Parking facilities, Part 2: Off-street commercial vehicle facilities 2018 cover

Standards Australia

Version:  Third Edition 2018.  (Current)
The objective of this Standard is to set out minimum requirements and recommendations for the provision of off-street parking, loading and manoeuvre areas for seven representative commercial vehicles classified according to limiting dimension and minimum turning circle.
AS 16321.4 (Int):2023 Eye and face protection for occupational use, Part 4: Protection against biological hazards 2023 cover

Standards Australia

Version:  First Edition 2023.  (Current)
AS 16321.4 (Int):2023 provides specifications and guidelines relating to products that provide eye and face protection from biological hazards.
AS 1554.2:2021 Structural steel welding, Part 2: Stud welding (steel studs to steel) 2021 cover

Standards Australia

Version:  Fifth Edition 2021.  (Current)
This Standard prescribes requirements for the stud welding of steel studs to steel elements, such steel studs being used for the attachment of members and connection devices to concrete (as concrete anchors and as shear connectors in composite steel and concrete construction), and for the fastening of other members and appurtenances.
AS 1141.6.2-1996 Methods for sampling and testing aggregates, Method 6.2: Particle density and water absorption of coarse aggregate - Pycnometer method 1996 cover

Standards Australia

Version:  First Edition 1996.  (Current)
Specifies the method for determining particle density, apparent particle density and water absorption of aggregate substantially retained on a 4.75 mm sieve by soaking in water, weighing surface dry, weighing in a pycnometer and weighing oven dry.
AS 1141.28:2014 Methods for sampling and testing aggregates, Method 28: Ball mill value 2014 cover

Standards Australia

Version:  Second Edition 2014.  (Current)
This Standard sets out the method for the determination of the Ball mill value of rock spalls, drill cores and ripped or broken rock.
AS 1141.2:2015 Methods for sampling and testing aggregates, Method 2: Basic testing equipment 2015 cover

Standards Australia

Version:  Third Edition 2015.  (Current)
Sets out requirements for basic equipment used in the performance of tests of the AS 1141 (AS/NZS 1141) series. Calibration and maintenance requirements for equipment are included in this Standard, which are intended to apply to the equipment listed in this Method and to equipment required in other parts of the AS 1141 (AS/NZS 1141) series.
AS 1141.16-2007 Methods for sampling and testing aggregates, Method 16: Angularity number 2007 cover

Standards Australia

Version:  Second Edition 2007.  (Current)
This Standard sets out the method for determining the angularity number of an aggregate. The angularity number is a measure of relative angularity based on the percentage voids in an aggregate after compaction in the prescribed manner.
AS 1141.25.3-2003 Methods for sampling and testing aggregates, Method 25.3: Degradation factor - Fine aggregate 2003 cover

Standards Australia

Version:  First Edition 2003.  (Current)
This Standard sets out the method for the determination of the degradation factor of fine aggregate or the fine portion of a mixed aggregate. It categorizes the fines produced by selfabrasion in the presence of water.
AS 1141.20.1-2000 Methods for sampling and testing aggregates, Method 20.1: Average least dimension - Direct measurement (nominal size 10 mm and greater) 2000 cover

Standards Australia

Version:  First Edition 2000.  (Current)
This Standard sets out the counting method for determining the average least dimension of aggregate particles by the use of vernier callipers or dial gauge or a slotted gauge. The method is applicable to aggregate of nominal size 10 mm and greater for sprayed bituminous surfacing.