Search all content

591 - 600 of 2265 results
AS/NZS 2111.6:1996 Textile floor coverings - Tests and measurements, Method 6: Determination of tuft length of pile 1996 cover

Standards Australia/Standards New Zealand

Version:  First Edition 1996.  (Current)
This Standard describes the procedure for determining the average tuft length of the pile of a textile floor covering.
AS 1100.301-2008 Technical drawing, Part 301: Architectural drawing 2008 cover

Standards Australia

Version:  Second Edition 2008.  (Current)
Provides architects, builders, drafting officers and others in the building industry with a common method for the representation of buildings and their components to enable the preparation and unambiguous interpretation of architectural drawings.
AS/NZS 61439.2:2016 Low-voltage switchgear and controlgear assemblies, Part 2: Power switchgear and controlgear assemblies (IEC 61439-2, Ed. 2.0 (2011), MOD) 2020 cover

Standards Australia/Standards New Zealand

Version:  First Edition 2016.  (Pending Revision)
Adopts IEC61439-2, Ed. 2.0 (2011) to define specific requirements of power switchgear and controlgear assemblies (PSC-ASSEMBLIES).
AS 1012.11-2000 Methods of testing concrete, Method 11: Determination of the modulus of rupture 2000 cover

Standards Australia

Version:  Third Edition 2000.  (Current)
This Standard sets out a method for determining the modulus of rupture of concrete testspecimens prepared in accordance with AS 1012.8.2 tested as simple beams with third-pointloading.
AS/NZS 4357.2:2006 Structural laminated veneer lumber (LVL), Part 2: Determination of structural properties - Test methods 2006 cover

Standards Australia/Standards New Zealand

Version:  First Edition 2006.  (Current)
Specifies test methods for the determination of structural properties of structural laminated veneer lumber (LVL).
AS 1379-2007 Specification and supply of concrete 2007 cover

Standards Australia

Version:  Fourth Edition 2007.  (Pending Revision)
Sets out minimum requirements for the materials, plant and equipment used in the supply of concrete; the production and, if applicable, the delivery of concrete in the plastic state; specifying, sampling, testing and compliance with specified properties of plastic and hardened concrete; and the uniformity of mixing.
AS/NZS 5000.1:2005 Electric cables - Polymeric insulated, Part 1: For working voltages up to and including 0.6/1 (1.2) kV 2005 cover

Standards Australia/Standards New Zealand

Version:  Third Edition 2005.  (Current)
Specifies the construction, dimensions and test requirements for single- and multicore cables insulated with polymeric materials intended for use at working voltages up to and including 0.6/1 (1.2) kV. It does not apply to polymeric insulated cables for special installations and service conditions or for which there are separate Australian/New Zealand Standards.
AS/NZS 1050.8:1994 Methods for the analysis of iron and steel, Part 8: Determination of manganese content - Spectrophotometric method 1994 cover

Standards Australia/Standards New Zealand

Version:  First Edition 1994.  (Current)
Specifies a spectrophotometric method for the determination of manganese content between 0.01 percent and 2 percent in all types of iron and steel.
AS/NZS 1050.24:1994 Methods for the analysis of iron and steel, Part 24: Determination of aluminium content - Spectrophotometric method 1994 cover

Standards Australia/Standards New Zealand

Version:  First Edition 1994.  (Current)
Specifies a spectrophotometric method for the determination of aluminium content in the range of 0.002 percent to 1.4 percent aluminium in all types of iron and steel. The method uses a mercury cathode, followed by solvent extraction to separate interfering elements, with alizarin red S to produce a chromogen which is measured at a wavelength of 490 nm.
AS/NZS 2111.4:1996 Textile floor coverings - Tests and measurements, Method 4: Determination of surface pile mass above the substrate 1996 cover

Standards Australia/Standards New Zealand

Version:  First Edition 1996.  (Current)
This Standard describes the procedure for determining the mass per unit area of surface pile, which can be cut from above the substrate of a textile floor covering. The surface pile mass per unit area can be expressed at its equilibrium condition or in terms of clean conditioned mass at agreed commercial allowances.