Search all content

741 - 750 of 1766 results
AS 2688:2017 Timber and composite doors 2017 cover

Standards Australia

Version:  First Edition 2017.  (Current)
Sets out requirements for the selection, identification, installation, finishing, and maintenance of timber and composite doors and doorsets for internal and external application.
AS 2796.1-1999 Timber - Hardwood - Sawn and milled products, Part 1: Product specification 1999 cover

Standards Australia

Version:  First Edition 1999.  (Current)
Specifies product requirements for sawn and milled hardwood products. Moisture content, profiles, tolerances and grades are covered. Requirements are also given for glued laminating, finger jointing and end-matching. Guidance is given on information to be supplied when ordering.
AS/NZS 2350.8:2006 Methods of testing portland, blended and masonry cements, Method 8: Fineness index by air permeability method 2006 cover

Standards Australia/Standards New Zealand

Version:  Second Edition 2006.  (Current)
This Standard describes the reference method for determining the fineness index of cement by the air permeability method, expressed in terms of surface area in square metres per kilogram of cement determined at a temperature of 23 ±2°C.
AS 2550.4-2004 Cranes, hoists and winches - Safe use, Part 4: Tower cranes 2004 cover

Standards Australia

Version:  Second Edition 2004.  (Pending Revision)
Specifies requirements for the safe use of tower cranes, covering planning, selection, siting, personnel, inspection, testing, erection, dismantling, personnel safety, operation, maintenance and repair. Appendices provide typical inspection and testing certificates as well as inspection testing check sheets.
AS/NZS 3582.3:2016 Supplementary cementitious materials, Part 3: Amorphous silica 2016 cover

Standards Australia/Standards New Zealand

Version:  Second Edition 2016.  (Current)
The objective of this Standard is to set out the requirements for amorphous silica for use as a cementitious material in concrete, mortar and related applications.
AS 4046.3-2002 Methods of testing roof tiles, Method 3: Determination of transverse strength 2002 cover

Standards Australia

Version:  Second Edition 2002.  (Current)
This Standard sets out the method for determining the transverse strength of roof tiles after immersion in water for 24 h.
AS 4046.0-2002 Methods of testing roof tiles, Part 0: Introduction and list of methods 2002 cover

Standards Australia

Version:  Second Edition 2002.  (Current)
Specifies a list of test methods for testing roof tiles used for domestic, commercial or light industrial applications.
AS/NZS 1050.21:1994 Methods for the analysis of iron and steel, Part 21: Determination of cobalt content - Spectrophotometric method 1994 cover

Standards Australia/Standards New Zealand

Version:  First Edition 1994.  (Current)
Specifies a spectrophotometric method for the determination of cobalt content up to 12 percent in all grades of iron and steel containing less than 10.0 percent copper. The sample is dissolved in acid and nitroso-R-salt added. This forms a red-brown chromophore which is measured spectrophotometrically at 580 nm.
AS 1012.14:2018 Methods of testing concrete, Method 14: Method for securing and testing cores from hardened concrete for compressive strength and mass per unit volume 2018 cover

Standards Australia

Version:  Third Edition 2018.  (Current)
Sets out a method for the securing, preparing and testing of cylindrical core specimens (cores) from hardened concrete for the determination of compressive strength and mass per unit volume.
AS/NZS 1050.27:1994 Methods for the analysis of iron and steel, Part 27: Determination of titanium content - Spectrophotometric method 1994 cover

Standards Australia/Standards New Zealand

Version:  Second Edition 1994.  (Current)
Specifies a spectrophotometric method using diantipyrylmethane as a chromogen, measured spectrophotometrically at 390 nm. The method can be used for the determination of titanium content between 0.005 percent and 1.20 percent in steel.